#?aB%> o0 Determine mounting location for panel.
Magazine: Installation Manual - Liberty Pumps. Determine mounting location for panel. Three phase duplex panels are designed to operate with three or four floats for pump sequencing. Cable connectors, are not required to be liquid-tight in NEMA, to rain, splashing water or hose-directed water, Do not use this product with flamable liquids, Do not install in hazardous locations as defined, primarily to provide a degree of protection against corrosion, windblown dust and rain, splashing, Cable connectors must be liquid-tight in NEMA. Be sure that oats have free range of motion without touching each other, or other equipment in the basin. In the hand mode, the pump will turn on unless other safety features are employed. Checking the float resistance - The float resistance can be measured to determine if the float is operating correctly or is defective. 
If distance exceeds the length of either the oat switch cables or the pump power cables, splicing will be required. You have already flagged this document.Thank you, for helping us keep this platform clean.The editors will have a look at it as soon as possible. 
Please reference the schematic provided with the control panel for proper installation.
endstream endobj startxref Troubleshooting the alarm light. 3.Mount oat switches at appropriate levels as illustrated in Figures 3-5. 157 0 obj <>stream On purchases of $500 for 6 months, or $1,000 for 12 months made with your Build.com Credit Card, Customer service wait times and delivery schedules may be impacted. Certain options will require alternative circuitry not including oat status and control/ alarm indicators. 2.Determine your normal operating level, as illustrated in. At this time the alarm will silence. Run conduit to junction box. Firmly tighten and seal all ttings on junction box. Make sure the. | /EDEb)R1!LJ>g|=pwW'u/Sq_u|#wkz:OPBG0pn+e&Re:EqZi`XT}*]FM"i.JVa Failure to follow these precautions could result in serious injury or death. The three float system is standard performing the common pump stop, lead pump start, and lag pump start/high level alarm functions. If using the mounting clamp; follow steps 4-6. A qualified service person must installand service this product according to applicableelectrical and plumbing codes.EXPLOSION OR FIRE HAZARDDo not use this product with flamable liquidsDo not install in hazardous locations as definedby National Electrical Code, ANSI/NFPA 70.Failure to follow these precautions could result in serious injury or death. Attach cable connectors and/or conduit connectors to control panel.
Mount control panel with mounting anges furnished with control panel. If a junction box is not required, connect pump and oat wires to proper position on terminals. Three Phase Duplex AE34=3-131, AE34=3-141, AE34=3-171, AE34=3-191, AE34=3-511, AE34=4-131, AE34=4-141, AE34=4-171, AE34=4-191, AE34=5-511, AE54=3-121, and AE54=4-121 Manufactured by SJE-Rhombus Installation Instructions and Operation/Troubleshooting Manual 7000 Apple Tree Avenue Bergen, New York 14416 Phone: 1-800-543-2550 Email: liberty@libertypumps.com www.libertypumps. Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software. | If distance exceeds the length of either the float switch cables or the pump power cables, splicing will be required. NOTE: All hose clamp components are made of 18-8 stainless steel material. The standard oat functions are common pump stop, lead pump start, lag pump start/alarm (three oats), or separate lag and alarm oats (four. Cable connectors are not required to be liquid-tight in NEMA 1 enclosures. water. Pull pump power cables and control switch cables through connectors into junction box.
Attach liquidtight connectors to junction box. :N$l* 6,7h-GZP6>Q|k09!g. The alarm system can be tested by moving the test/normal/ silence switch to the test position. A qualified service person must install and service this product according to applicable electrical and plumbing codes. The three float system is standard, performing the common pump stop, lead pump start, and lag pump start/ high level alarm functions. IfbpN5 -IzkBI[\L,sEm #zC7">H(K=x0=rcqXATC#c+Bp; C&VD~uyb4HvC$%jzWz1 Do not mount the junction box inside the sump or basin. oat and stripped ends (stop, lead, lag, alarm, etc.). Cable connectors are not required to be liquid-tight in NEMA 1 enclosures.
hb```f``Je`e` ,@Q bbNs``1!DII/# NEMA 4X enclosures are for indoor or outdoor use, primarily to provide a degree of protection against corrosion, windblown dust and rain, splashing water and hose-directed water. Subscribe now for coupons, exclusive deals, and design inspiration! 2.Mount control panel with mounting anges furnished with control panel. 5.Attach cable connectors and/or conduit connectors to control panel. Check local codes and schematic for the number of power circuits required. This product must be installed in accordance with National ElectricCode, ANSI/NFPA 70 so as to prevent moisture from entering or accumulating within boxes, conduit bodies, fittings, float housing, or cable.Warranty void if panel is modified.Call factory with servicing questions:1-800-543-25507249000B. hA v0W|d'XDsx9sx99s| 0 0 You must use conduit sealant to prevent moisture or gases from entering the panel.
The four oat system utilizes separate oats for lag pump start and high level alarm.
oat cable is not allowed to touch the excess hose clamp band during operation. %%EOF On purchases of $500 for 6 months, or $1,000 for 12 months made with your Build.com Credit Card. The pump circuit has a thermal-magnetic circuit breaker which provides pump disconnect and branch circuit protection. See your SJE-Rhombus supplier for replacements. For outdoor or wet installation, we recommend the use of a SJERhombus liquid-tight junction box with liquidtight connectors to make required connections. Please reference the schematic provided with the control panel for proper installation. Are you sure you want to delete your template? Faucet.com strongly opposes the practice of sending unsolicited email for commercial purposes, otherwise known as "spam." Your file is uploaded and ready to be published. NEMA 1 enclosures are for indoor use only, primarily to provide a degree of protection against contact with enclosed equipment. 133 0 obj <>/Filter/FlateDecode/ID[<69EF877816F39241A7029363E8216C8C><8F71E50BE14FE245839B5401286075F5>]/Index[112 46]/Info 111 0 R/Length 99/Prev 335863/Root 113 0 R/Size 158/Type/XRef/W[1 2 1]>>stream 4.Drill proper size holes for type of connectors being used. H\n0E If the light does not activate, replace with bulb of same type. Most single phase duplex panels are designed to operate as three or four oat systems. 20122022, manualsdir.comAll rights reserved. Identify and label each wire before pulling through conduit into control panel and junction box. 1.Determine mounting location for panel. See schematic for oat options. Installation Instructions FIGURE 1: Three float duplex Most three phase duplex panels are designed to operate with three or four float systems. Liberty Pumps Three-Year Limited Warranty *NOTE: Liberty Pumps, Inc. assumes no responsibility for damage or injury due to disassembly in the field. Hooray! Make sure the, Determine mounting location for panel. Cable connectors must be liquid-tight in NEMA 4X enclosures.ELECTRICAL SHOCK HAZARDDisconnect power before installing or servicingthis product. to prevent moisture or gases from entering the panel. 10.Firmly tighten and seal all ttings on junction box. Replace the float if you do not get this reading. The three oat system is standard performing the common pump stop, lead pump start, and lag pump start/high level alarm functions. Disconnect power before installing or servicing this product. AE Series Duplex Pump Control Panel with Alarm, Provides reliable alternating operation of two pumps with automatic override control in residential or commercial installations, Constructed of NEMA 4X ultraviolet stabilized thermoplastic, Includes sump basins, effluent/sewage pump chambers, lift stations and audible alarm, Covered under Liberty Pump's 3 year warranty, Magnetic motor contactor controls pump by switching hot electrical lines, Terminal block design for easy service and maintenance. NEMA 1 enclosures are for indoor use only, primarily to provide a degree of protection against contact with enclosed equipment.
Use the following procedure to measure the float resistance. 8.Run conduit to junction box. NEMA 4X enclosures are for indoor or outdoor use, primarily to provide a degree of protection against corrosion, windblown dust and rain, splashing water and hose-directed water. Float Controls Check the floats during their entire range of operation. If the liquid level tips the lag/alarm oat, the lag pump will start and the audio/visual alarm will activate. The standard float functions are common pump stop, lead pump start, lag pump start/alarm (three floats), or separate lag and alarm floats (four floats). NEMA 1 enclosures are for indoor use only,primarily to provide a degree of protection against contact with enclosed equipment. This control panel must be installed and serviced by a licensed electrician in accordance, All conduit running from the sump or tank to the control panel must be sealed with conduit sealant. Lights will illuminate when control/alarm power is supplied. All conduit running from the sump or tank to the control panel must be sealed with conduit sealant to prevent moisture or gases from entering the panel. 2. The four float system utilizes separate floats for each function. endstream endobj 3076 0 obj <>stream Please send your email only to those friends who will be interested. Both pumps will remain on until the liquid level drops to normal and all three oats are in the OFF (open) position. Failure to follow these precautions could result in serious injury or death. Cable connectorsare not required to be liquid-tight in NEMA 1 enclosures. Do not use NEMA 1 enclosures if subjected to rain, splashing water or hose-directed water. This product must be installed in accordance with National Electric Code, ANSI/NFPA 70 so as to prevent moisture from entering or accumulating within boxes, conduit bodies, fittings, float housing, or cable. Place the ohmmeter dial to read ohms and place on the R X 1 scale.
Installation Instructions Most single phase duplex panels are designed to operate as three or four float systems. Check local codes and schematic for the number of power circuits required. This product must be installed in accordance with National Electric. View cart for details. Over tightening may result in damage to the plastic clamp. A hand-off-automatic switch is provided for each pump.
Pull pump power cables and control switch cables through connectors into junction box. See schematic inside control panel for terminal layouts. Replace product immediately if switch cable becomes damagedor severed. Drill proper size holes for the type of conduit used. endstream endobj 113 0 obj <> endobj 114 0 obj <> endobj 115 0 obj <>stream 8. Insure all cable connectors are.
As the liquid level tips the lead oat, the lead pump will start. When both pumps have stopped running, the alternator will switch the lead pump and lag pump operating functions in the next sequence. Operations Single phase duplex panels are designed to operate with three or four floats for pump sequencing. Cable connectors must be liquid-tight in NEMA 4X enclosures. Attach liquidtight connectors to junction box. Do not use this product with flamable liquidsDo not install in hazardous locations as definedby National Electrical Code, ANSI/NFPA 70. A1n\shgsAKL?t/\[c@\ `@C@Tn*,? ia ;CXe*q1F58FGcC)K!Ve` H1` oxhh3. 0 4O Alarm System (Horn and Indicator - standard). Code, ANSI/NFPA 70 so as to prevent moisture from entering or accumulating within boxes, conduit bodies, fittings, float housing, or cable. Operations wired in series with the magnetic contactor coil so that on an overload trip, the magnetic contactor will be disabled. Access this product information directly from your mobile device, or share the product with someone else by sending it in a text message. Run conduit to junction box. You must use conduit sealant to prevent moisture or gases from entering the panel.
Insure all cable connectors are liquid-tight and sealed. Three Float Operation: As the liquid level rises to the stop oat and tips it to the ON (closed) position, the panel will remain inactive. Installation Instructions and Operation/Troubleshooting Manual, This control panel must be installed and serviced by a licensed electrician in accordance.
It's a very heavy, well built pump that I think will hold up to the demands placed on it. If in doubt, see the pump identication plate for electrical requirements. 11.If a junction box is not required, connect pump and oat wires to proper position on terminals. Normally closed - Contacts are closed under normal conditions and open when alarm condition is present. w;AHAcp"0,`$]-ADEE""hhHZs,;Xc| W This product is not. NOTE: Options ordered may affect the number of oats and their functions. Liberty Pumps, Inc. warrants that pumps of its manufacture are free from all factory defects in material and workmanship for a period of 3 years from the date of purchase. 1.Use oat label kit to identify and label cables on both. Over tightening may result in damage to the plastic clamp. Overall, I'm very satisfied with the pump and will be ordering another as a spare. 6.Determine location for mounting junction box according to local code requirements. Disconnect power before installing or servicing this product. Determine location for mounting junction box according to local code requirements. In the automatic mode, the pump will turn on from commands by the oat switch(es). NOTE: Do not install cord under hose clamp. When an alarm condition occurs, a red light and a horn will be activated. 5.Locate the clamp at the desired activation level and secure the clamp to the discharge pipe as shown in Figure 5. This product is listed under the following manufacturer number(s): All faucets sold within the United States must be low lead compliant. Alarm Horn Pressing the alarm test/normal/silence switch to the test position or activating the alarm float should turn on the alarm horn. Dry Auxiliary Contacts (standard feature).
112 0 obj <> endobj Upload manuals that we do not have and get. Keep these instructions with warranty after installation. new 0 Four Float Operation: The alarm will activate and remain on only if the alarm oat is tipped to the ON (closed) position. Single Phase Duplex AE21L=3, AE21H=3, AE21L=4, AE21H=4 AE24L=3, AE24H=3, AE24L=4, and AE24H=4 Manufactured by SJE-Rhombus Installation Instructions and Operation/Troubleshooting Manual 7000 Apple Tree Avenue Bergen, New York 14416 Phone: 1-800-543-2550 Email: liberty@libertypumps.com www.libertypumps.com This control panel must be installed and serviced by a licensed electrician in accordance with the National Electric Code NFPA-70, state and local electrical codes. NOTE: Be sure the incoming power, voltage, amperage, and phase meet the requirements of the pump motors being installed.
3.Determine conduit entrance locations on control panel. 9.Identify and label each wire before pulling through conduit into control panel and junction box. With the float in the off position, the scale should read infinity (high resistance). For outdoor or wet installation, we recommend the use of an SJERhombus liquid-tight junction box with liquidtight connectors to make required connections. 12.Connect control/alarm and pump power conductors to proper position on terminals. For outdoor or wet installation, we recommend the use of a SJERhombus liquid-tight junction box with liquidtight connectors to make required connections. Replace product immediately if switch cable becomes damaged or severed.
If distance exceeds the length of either the oat switch cables or the pump power cables, splicing will be required. Troubleshooting 3. 8. The run light will be ON in either the hand or the automatic mode when the pump is called to run. Three Float Operation: As the liquid level rises to the stop float and tips it to the ON (closed) position, the panel will remain inactive. Lights will illuminate when the respective oat is in the closed position. %PDF-1.6 %
Normally open - Contacts are open under normal conditions and closed when alarm condition is present.
"), Installation Instructions and Operation/Troubleshooting Manual, Email: liberty@libertypumps.com www.libertypumps.com. hbbd``b`@`K 5@e )q:"+Hp${3|W @R?"F_ %] NOTE: Some options ordered may not be included in this manual. 6.Tighten the hose clamp using a screwdriver.
If distance exceeds the length of either the float switch cables or the pump power cables, splicing will be required.
*=RequiredMessage & data rates may apply.View our Privacy Policy & Terms or Use.
endstream endobj 3068 0 obj <>/Metadata 341 0 R/Pages 340 0 R/StructTreeRoot 343 0 R/Type/Catalog/ViewerPreferences<>>> endobj 3069 0 obj >/PageWidthList<0 612.0>>>>>>/Resources<>/Font<>/ProcSet[/PDF/Text]/Properties<>/XObject<>>>/Rotate 0/StructParents 0/TrimBox[0.0 0.0 612.0 792.0]/Type/Page>> endobj 3070 0 obj <> endobj 3071 0 obj <> endobj 3072 0 obj <> endobj 3073 0 obj <> endobj 3074 0 obj <> endobj 3075 0 obj <>stream NEMA 4X enclosures are for indoor or outdooruse, primarily to provide a degree of protection against corrosion, windblown dust and rain, splashingwater and hose-directed water. Disassembly, other than at Liberty Pumps or its authorized service centers, automatically voids warranty. You must use conduit sealant to prevent moisture or gases from entering the panel. 4.Place the cord into the clamp as shown in Figure 5. See more Liberty PUMPS Ae24l 3 AE Series Duplex Pump Co Liberty Pumps AE24L=3 - AE Series Duplex Pump Control Panel w/ Alarm. I needed a substantial pump for a lift station in a small mobile home park, and this fit the bill. Keep these instructions with warranty after installation. Make wire splice connections at junction box. }P-0\{Tut~ $ Drill proper size holes for type of connectors being used. This control panel must be installed and serviced by a licensed electrician in accordance with the National Electric Code NFPA-70, state and local electrical codes. CAUTION: If control switch cables are not wired and mounted in the correct location, the pump system will not function properly. to prevent moisture or gases from entering the panel. Warning: Disconnect all incoming power to panel. Only a couple of things that were not exactly as advertised: there was no float switch as pictured and the output is 1 1/4", not 1 1/2". Single Phase DuplexAE21L=3, AE21H=3, AE21L=4, AE21H=4AE24L=3, AE24H=3, AE24L=4, and AE24H=4Manufactured by SJE-Rhombus Installation Instructions and Operation/Troubleshooting Manual7000 Apple Tree AvenueBergen, New York 14416Phone: 1-800-543-2550Email: liberty@libertypumps.comwww.libertypumps.comThis control panel must be installed and serviced by a licensed electrician in accordancewith the National Electric Code NFPA-70, state and local electrical codes.All conduit running from the sump or tank to the control panel must be sealed with conduit sealantto prevent moisture or gases from entering the panel. primarily to provide a degree of protection against contact with enclosed equipment. Clean, adjust, or replace damaged floats. >"o@73DsAs=#@8q:c?c=B&y3'3x.NaHe` When the alarm condition is cleared, the alarm system is reset. The four float system utilizes separate floats for lag pump start and high level alarm. WARNING: Turn off all power before installing oats in pump chamber. Do not use NEMA 1 enclosures if subjected to rain, splashing water or hose-directed water. With the float in the ON position, the scale should read nearly zero (very low resistance). See schematic inside control panel for terminal connections. Drill proper size holes for the type of conduit used. For information regarding the operations of options not listed here or servicing questions, please call a Liberty Pumps customer service technician at, The control circuit and alarm circuit are fused. NOTE: It is the recommendation of the factory to use separate pump and control/alarm power sources. FIGURE 1: Three float duplex NOTE: Options ordered may affect the number of floats and their functions. You must use conduit sealant to prevent moisture or gases from entering the panel. NEMA 4X enclosures are for indoor or outdoor use, Use oat label kit to identify and label cables on both, Determine your normal operating level, as illustrated in, Mount oat switches at appropriate levels as illustrated in, Place the cord into the clamp as shown in, Locate the clamp at the desired activation level and secure the clamp to the discharge pipe as shown in, Tighten the hose clamp using a screwdriver. buildinc, . Copyright 1995-2022 eBay Inc. All Rights Reserved. A qualified service person must install and service this product according to applicable electrical and plumbing codes. If the test/normal/silence switch is moved to the silence position, the horn will be silenced. As the liquid level tips the lead float, the lead pump will start. Both types automatically reset once alarm condition is cleared. hmo9w-U&mCE%vaeKo^`g>Pq&a2[&.
See schematic inside control panel for terminal connections. HtW[E~_{C9DD$C_]zfvg/?z]p_-O]Jp2iZj-fRo?rm"?ke ~V*1;p]5V)*.+U?JrGl Rq}[ |iV!jXcWE_R5PU=WS;5kX4X`lL|]h8cSMWSuU\`M[u&zPf@2;'w&_8c6Vw)|ddoDUj`9Vv^lw1u);841=IMG9AZ #{D1O_$O) P*^}$M . K,M\ any latin characters (a-z, A-Z) any numbers (0-9) special characters ("-", "_" and ".
Please visit the, AE Series Duplex Pump Control Panel with Alarm, FREE Standard Ground Shipping on Orders over $49, Provides reliable alternating operation of two pumps with automatic override control in residential or commercial installations, Constructed of NEMA 4X ultraviolet stabilized thermoplastic, Includes sump basins, effluent/sewage pump chambers, lift stations and audible alarm, Covered under Liberty Pump's 3 year warranty, Magnetic motor contactor controls pump by switching hot electrical lines, Terminal block design for easy service and maintenance. Determine conduit entrance locations on control panel. This email will not be used for purposes other than the one clearly stated above.
NOTE: If using conduit, be sure that it is of adequate size to pull the pump and switch cables through.