NewLife Elite Service Manual 5.14 Flowmeter Replacement 5.14.1 Flowmeter Removal 1 Set the units ON/OFF switch to the OFF position, and unplug the power cord. TheAirsep Intensity Concentratorseries offers a choice between single or dual flow oxygen concentrator service. A dual flow concentrator allows two patients to be served from the same oxygen concentrator, providing reduced power consumption and fewer oxygen concentrator purchases. 
6 Install the rebuild kit, which contains all parts of the solenoid assembly except the solenoid coil. Equipment Providers, based on their expertise and documentation, may establish and implement their own protocol to check oxygen concentration.
%PDF-1.4 %
0000004239 00000 n This enables proper treatment as prescribed by a qualified, licensed physician. It is very important to tighten all tubes to eliminate leaks. Replace compressor. 1 Set the units ON/OFF switch to the OFF position, and unplug the power cord. 4 2. 5.12 Buzzer Replacement 1 Set the units ON/OFF switch to the OFF position, and unplug the power cord. 2 Remove the caster nut with a 9/16-inch socket. NewLife Elite Service Manual 5-17 10 Pull the power cord through the opening on the power cord receptacle. 0000102881 00000 n If the alarm does anything other than sound loudly for five seconds, instruct the patient to call the Equipment Provider immediately. Defective circuit board. 4 Unscrew the circuit breaker while you apply pressure to the circuit breaker retaining ring. 4 Make sure the unit is cycling properly by following the green valve lights on the circuit board. startxref 0000003163 00000 n 1 2 3 4 5A 5B 6 7 8 9 10 11A 11B 11C 11D Part No. 2 Remove the left side panel. 6 Reconnect the side panel.
0000028032 00000 n To ensure that the units output of oxygen is within specification, you must perform a test of oxygen concentration. Check circuit board for two-light rotation/replace circuit board. 0000004892 00000 n xref wide, 14.5 in. Manufactured by AirSep, the concentrator is also available as an 8 Liter Concentrator. These responsibilities are outlined below and throughout this manual. 3 Set the units ON/OFF switch to OFF, and unplug the power cord. This allows oxygen to flow out of the top. Check electrical connections. To replace the capacitor, take the following steps: 5.4 1 Set the units ON/OFF switch to the OFF position, and unplug the power cord. Leak. :vZ NewLife Elite Service Manual 5 Install the new pressure switch, connect the leads, and leak test. NewLife Elite Service Manual 5.0 Service 5.1 Components The design of the AirSep NewLife Oxygen Concentrator allows for easy access and removal of most components. 6 Reconnect the back and side panels. Power-efficient, saving you electric expenses. Defective circuit board. Test the unit upon delivery to a patient and at periodic intervals. NewLife Elite Service Manual 2.0 Operation Check and Oxygen Concentration Test 2.1 Description of Operation Air enters the NewLife Oxygen Concentrator through an external air intake gross particulate filter. 5.4. The PSI, though, is never split; if the flow is spilt, both sides will deliver at 20 PSI. 4 Unscrew the flowmeter nuts with a wrench. 7 Clean or replace the seat. 6 Remove the seat. NewLife Elite Service Manual 5.11.2 ON/OFF Power Switch Installation 5.12 Buzzer Replacement 5.14 Flowmeter Replacement 5.13 Hour Meter Replacement 5.14.1 5.14.2 Flowmeter Removal Flowmeter Installation 5.15 Power Cord Replacement 5-15 5-15 5-15 5-16 5-16 5-16 5-16 Section 6.0 Troubleshooting 6.1 Operating Pressure Test 6-1 6.1.1 High Operating Pressure 6-1 6.1.2 Low Operating Pressure 6-2 6. The five-green-light matrix corresponds to the valve configuration of the NewLife unit. Circuit Board Replacement The solid-state printed circuit board controls the sequential timing operation of the five solenoid valves and the alarm system functions. 224 32 5 Turn the flowmeter adjustment knob counterclockwise until it stops (wide open). You must explain that the purpose of this therapy is to alleviate symptoms. NewLife Elite Service Manual 4 Install the new filter with the inlet side in the same position as before. NewLife Elite Service Manual 5.8 Product Regulator Check and Setting The product regulator enables you to set the maximum flow of oxygen output by the NewLife unit. Faulty solenoid valve. 0000000016 00000 n KI070-1 SC003-2 WA002-8 CL007-1 HX002-1 HX002-2 F0104-1 VA005-1 F0045-2 VA008-1 F0006-4 CO006-1R(T/N) CO006-4R(T/N) CO006-9R(T/N) CO006-10R(T/N) Description Kit, Vibration, Spring Mount includes bumpers/capacitor bracket (not shown) #6 Phillips 3/8 Long #6 Washer Clamp, Hose 3/8 Heat exchanger, Medserv Heat exchanger (Elite) Fitting, brass, Comp. Check wall outlet for power. 0000103143 00000 n NewLife Elite Service Manual 4.2.1 Preparing for New Patient Use When you remove the NewLife from a patients home, always dispose of the used nasal cannula and humidifier bottle. 3 Turn the flowmeter adjustment knob counterclockwise until it stops (wide open). No open flames within five feet of this device, oxygencarrying tubing, or accessories. AirSep NewLife Intensity Ten Oxygen Concentrator Features & Benefits, AirSep NewLife Intensity 10 Oxygen Concentrator Safety Features. 0000002190 00000 n Keep all openings to the sieve beds sealed. Use an extension for the two front caster nut removals. 0000004015 00000 n 5 Disconnect the two leads to the capacitor and remove if necessary. Product Numbers: AS099-1, AS099-4, AS099-100, AS099-101. <<22D0D1E340A660439D8582C206C3437B>]>>
NewLife Elite Service Manual Expedited Product Warranty Check service is always at your fingertips with AirSep: http://www.airsep.com/Support/Warranty_Information.aspx OR In the US or Canada, dial 866-873-9277 AirSep is a registered trademark of AirSep Corporation. NewLife Elite Service Manual NOTE Adjust the product regulator fully counterclockwise to unload the spring. The maximum flow should register 5.5 lpm (the 5.5 lpm line should appear to split the middle of the flowmeter ball) with no connections at the oxygen outlet. 0000034528 00000 n 5.10. They identify safety guidelines or other important information as follows: 1-2 WARNING: Describes a hazard or unsafe practice that can result in severe bodily injury or death. The Airsep Intensity 10 also has a high pressure capacity of 20 psig, which is approximately three times higher than most oxygen concentrators. 2 Allow the unit to run for three minutes. AirSep Newlife Intensity Conentrator Airsep NewLife Intensity Read more AirSep Freestyle 5 Portable Concentrator Description The Read more AirSep VisionAire 5L Simple to use and Read more AirSep VisionAire 3L Conentrator VisionAire 3 Oxygen Concentratorby AirSep Read more AirSep FreeStyle 3 Portable Concentrator AirSeps FreeStyle Read more Sequal Regalia 10 LPM Regaliais a high-grade, Read more VisionAire 3 Caire Airsep Visionaire 3 liter oxygen concentrator Read more Airsep NewLife Intensity 8 The AirSep NewLife Read more For privacy reasons YouTube needs your permission to be loaded. Worn compressor. A continuous alarm sounds for approximately five seconds to indicate a good battery. Invacare Perfecto 2 Series Concentrator User Manual, Devilbiss 5 Liter Concentrator User Manual, Devilbiss 10 Liter Concentrator User Manual, Respironics Everflo Concentrator User Manual, Respironics Millennium Concentrator User Manual, AirSep Visionaire Concentrator User Manual, AirSep Newlife Elite Concentrator User Manual, Invacare PlatinumConcentrator User Manual, HOMEFILL COMPRESSORS & CONSERVING CYLINDERS, Respironics System One CPAP with C-Flex User Manual, Respironics System One Humidifier User Manual, Nonin /Respironics 3150 Wrist Oximeter User Manual, Invacare Semi or Full Electric Hospital Bed User Manual, Mendo-Lake Home Respiratory Services 843 Parallel Drive Lakeport, CA 95453 Phone: (707) 263-9888 Fax: (707) 263-9889. Two green lights should always illuminate and rotate (cycle) during normal operation. Low oxygen concentration. Defective flowmeter. Airsep NewLife Intensity 10 Oxygen Concentrator is a high flow oxygen concentrator that delivers up to 10 LPM of continuous oxygen. Leak test and repair leak. 0000006147 00000 n Compressor The compressor is the pump within the oxygen concentrator that pushes the room air into the bottom of the sieve beds. Low flowmeter blocks for pediatric or other low flow applications. Confirm that the circuit board and solenoid valves function properly. 5 With a slotted screwdriver, push in on the board support tabs, while you lift each corner of the circuit board. 2 Remove the side and lower front panels. deep (72.4 cm high, 40.0 cm wide, 36.8 cm deep) Weight: 54.0 lb; shipping weight - 59.0 lb (24.5 kg; shipping weight - 29.0 kg) Electrical Requirements: 120 VAC, 60 Hz, 4 amps, 350 watts 230 VAC, 50 Hz, 4 amps, 350 watts Capacity: 5 liters per minute at 90% oxygen (Based on 70F [21C] at sea level) Accuracy: Flowmeter 5% full scale. 3 Install the new caster and washer, and tighten the nut.
11 Using same distance located on old power cord, slide the strain relief onto the new power cord with the lip of the strain relief facing the ends of the power cord leads. 224 0 obj <> endobj NewLife Elite Service Manual Problem Probable Cause Solution Compressor runs with intermittent low pressure alarm and low oxygen concentration. 0000000936 00000 n Defective sieve beds. Replace flowmeter. 4.1.5 Recording Maintenance As the Equipment Provider, you can record all routine maintenance and repairs performed on the NewLife unit, including hours and dates of service. 7 Turn the regulator knob clockwise until the flowmeter ball centers on the 5.5 lpm line.
NewLife Elite Service Manual 5.2.6 Caster Replacement 5.3 1 Remove the cabinet panels to expose the caster nut. NewLife Elite Service Manual NOTE It may be desirable to provide one additional liter of flow if you use the lockout feature. SEND INSTRUCTIONS TO PATIENT OR CAREGIVER, AirSep Freestyle 5L- Portable Instructions. 0000003979 00000 n 6-6 Probable Cause Solution Improperly set or faulty product regulator. WARNING NewLife units must not be used for or with any lifesupporting applications. Repair or replace solenoid valve. Pressurized air then exits the compressor and passes through a heat exchanger. This filtered air enters the compressor via a suction resonator, which quiets the compressors suction sound. The AirSep NewLife Intensity concentrator can also provide low flow meter blocks to serve pediatric applications. Align. 5.9 4 Remove the diaphragm. NewLife Elite Service Manual 1.3 Functional Specifications Dimensions: 28.5 in. If not, refer to Section 5.8.1 to set the product regulator. The maximum combination between the two flow meters is 10 LPM which is the concentrators maximum output. Clean the exterior of the NewLife with a soapy water solution or commercial cleaner to remove any gross debris, organic or otherwise. NewLife Elite Service Manual 6.3 Troubleshooting Chart Problem Compressor does not run. 3 Turn flowmeter completely open, up to the highest setting. 3 Disconnect the two leads to the capacitor and slide capacitor out of the tie wrap holding it in place. NewLife Elite Service Manual 1.0 Introduction 1.1 Equipment Provider Responsibility All Equipment Providers of the NewLife Elite/NewLife Oxygen Concentrator must assume responsibilities for handling, operational check-out, patient instruction, and maintenance. 4 Push in on the locking tab to the alarm 6-pin connector to disconnect it. 2 Set the units ON/OFF switch to the ON position, and allow the unit to run at least three minutes to build up pressure. This makes disassembly and reassembly easier. Or one flow meter can be set to 3 liters and the other at 7 liters. (Clean or replace it.) 5.4.2 Feed or Waste Valve Reassembly To reassemble the feed or waste valves, follow the feed or waste valve rebuilding procedure in reverse order, and test for leaks. NewLife Elite Service Manual NOTE If a pressure transducer circuit board, cut tie-wrap at circuit board and disconnect green 1/4-inch tube. 0000008956 00000 n 0000010348 00000 n
The ball should rest at 5.5 lpm. Use the following procedure to test the operating pressure of the unit. 0 trailer 3 Disconnect the circuit breaker leads. 4 Reconnect the cabinet panels. 0000004126 00000 n NewLife Elite Service Manual 5.3.1 Compressor Replacement Compressor Assembly Removal To remove the compressor assembly for exchange, follow the steps listed below: 1 Set the units ON/OFF switch to the OFF position, and unplug the power cord. 0000092174 00000 n An optional oxygen monitor is available to determine the actual oxygen output of theIntensityat any given instance, helpful for those on a specified prescription dose or those living at higher altitudes. NewLife Elite Service Manual Section 5.0 Service 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 Components 5-1 5.2.1 Removing Side Panel(s) 5-1 5.2.3 Removing Lower Front Cover Cabinet Removal 5.2.2 5.2.4 5.2.5 5.2.6 Removing Back Panel Removing Control Panel Superstructure Caster Replacement Compressor 5.3.1 5.3.2 Compressor Replacement Capacitor Replacement Solenoid Valves 5.4. 5.14.2 Flowmeter Installation To install a new flowmeter, follow the flowmeter removal procedure in reverse order. 3 If used, connect the humidifier bottle, oxygen tubing, and cannula to the oxygen outlet. NewLife Elite Service Manual 3.2.2 Checking the Alarm System Battery The alarm system battery is tested each time the ON/OFF switch is set to the ON position. 0000004491 00000 n NewLife Elite Service Manual 1.2 Important Notice and Symbol Explanations As you read the manual, pay special attention to the WARNING, CAUTION, and NOTE messages. Leak test and repair leak. CAUTION For your safety, be sure to set the ON/OFF switch to the OFF position and unplug the power cord of the unit before you service the NewLife Oxygen Concentrator. 5 Remove the flowmeter through the control panel. Test the unit upon delivery to a patient and at periodic intervals. Take advantage of the massive savings of a single unit for two patients! NewLife Elite and NewLife are registered trademarks of AirSep Corporation. 0000018374 00000 n NewLife Elite Service Manual 5.7 6 Connect the fan leads, and install the cabinet fan screws. 0000015725 00000 n The lights should follow the label below the circuit board and two lights should be activated at all times. To check for leaks, take the following steps: 1 Plug in the unit. 4 Remove the right side panel. 4 Disconnect the blue compressor lead at the terminal strip and the brown lead at the temperature switch. Reset or replace circuit breaker. The heat exchanger reduces the temperature of the compressed air. NewLife Elite Service Manual Appendix Exploded Drawings Control Panel Assembly A-1 Main Structure Assembly A-2 Base and Cabinet Components A-3 Test Block Assembly A-4 Valve Block Assembly A-5 Compressor Assembly A-6 Adsorption Bed Assembly A-7 AirSep Corporation. 5 Set the ON/OFF switch to the ON position to test the alarm.