Unfasten the two screws underneath the front bumper with a Phillips screwdriver. b) Jeff Bipes Angel Eyes fitment guide (Step by Step IMAGES ONLY) Cookie Policy -
It's my daily run around and makes no sense to sell it. JavaScript is disabled. Removing: Adjustment screws on left headlight shown. 
Is there any thing involved in realigning the bumper to the body so it fits straight? Remove the Torx screws with a Torx screwdriver and lift the front bumper off the Audi TT, setting it aside. problem is, ive never removed a bumper on a TT and im having a little trouble ive gotten all the torx bolts out that i can see and the ones in the wheel well but it seems like there is something still attached, maybe im missing something. 8N0941 004 AQ JavaScript is disabled. Below is a picture of the bumper pulled out
to show you, just inside the wing there is a single torx screw facing vertically
down which must be released. It can be taken off, take it to a body shop to have the holes filled and repainted. TIP: If your car is too low for a trolley
jack, drive onto a piece of thick wood to give you height for the jack. Detach the two bolts---one on each side---in front of the tires in the wheel wells with a socket wrench. Detach trim toward the front. Remove the 2 large Philips screws from the
lower front bumper. Disconnect battery Looking good Tony and glad you found someone who met your (high) standards! about how long does it take to remove the front bumper and how hard is it to reassemble? 3 Lateral adjustment screw, Turn adjustment screws to achieve specification. Detach trim toward the front. Before installing trim -4-, it is necessary to press clips -2- into fender -3-. Jack up the car and remove the front wheels, Use axel stands
for safety. I've got mine down to about 15-20mins now and I also find that its much easier to re-align once it's been off a few times. Andre, Do you have a section or link for simple schematic on how everything is powered CAUTION! Fill in your details below or click an icon to log in: You are commenting using your WordPress.com account. The following errors occurred with your submission, Discussion forum for the Mk1 Audi TT Coupe & Roadster produced from 2000-2006, The New Marketplace (All new FS items go in here), Vehicles For Sale - Archive (NO NEW POSTS HERE), Parts For Sale - Archive (NO NEW POSTS HERE), Want To Buy - Archive (NO NEW POSTS HERE). (LogOut/ How about tools, like is there any torx or other non common tools needed to do this? 17 Combi bolt: 2.5 Nm. The Fora platform includes forum software by XenForo, http://forums.audiworld.com/tt/msgs/1666083.phtml. Remove headlight housing from opening. seeking any advice on removal of the lower rear bumper panel along with the front bumper-grill on a TT. 8N0941 004 S Front bumper, removing, installing and assembly overview. one question though where did you get the diagrams? Remove the indicated Torx Screws to release the front of the
wheel arch liner and push it to one side to allow access to the chamber behind
the bumper. The process is quite long for the DIY guy that is at his first try. vwvortex.com is not in any way affiliated with Volkswagen AG. Release quick-release fasteners on wheel housing liners and noise insulation (FIG2)
Contact Us - 12 Guide profile Detach front part of wheel housing liner Lower the vehicle so it is resting on the jack stands. 9 Bumper any help would greatly be appreciated.. thanxxx. 15 Wheel spoiler You can save time and money by removing the front bumper yourself. It is possible to just purchase the lens somewhere. There are 4-10mm nuts that require a deep socket and long extension to remove. To detach wheel housing liner, release quick-release fasteners -arrow B-. For a better experience, please enable JavaScript in your browser before proceeding. Come join the discussion about methods, materials, equipment, restoration, classifieds, troubleshooting, and more! you can remove the tumors.. it leaves about 30 holes in the bumper that need to be filled. Remove the Front Bumper Detach the battery cover on the driver's side of the engine compartment near the front, removing the plastic pegs with a flat-head screwdriver. Thanks for the info. Great HOw to by the way with links and headlight removal.. The front bumper can be removed without too much trouble, allowing you to customize the appearance of the TT to fit your individual style. It's an 04 8N 3.2. I had a 53 plate years ago and swapped the center lower bumper trim for a V6 version (honeycombe pattern) - i think it had 2 plastic fixings (push the centres in and out they pop) then swivelled outwards and pulled backwards to release tabs along the top. They are from Bentley Publishers. There are a number of front bumper designs for you to choose from to enhance the appearance of your car. I would use Waks guide as the primary guide and use the two other ones if questions occur. The Fora platform includes forum software by XenForo, Pre-wash stages: Washing, Drying, Clay & Detailing, VerticalScope Inc., 111 Peter Street, Suite 600, Toronto, Ontario, M5V 2H1, Canada.
Pull the bumper down carefully and locate the Torx screws inside the ends of the bumper. theyre fantastic! Currently Active Users Viewing This Thread: 1, The following errors occurred with your submission. Did you find the answer yet? Expanding clips must be pressed into fender before installing trim -1- (FIG1) Only accessible after removal of wheel housing liner An extension is helpful reaching the 10mm nuts (2 10mm nuts on each). Contact Us - Content on vwvortex.com is generated by its users. The Powertrack Insert; The best way to improve your Haldex first generation traction! Advertising - 1 Pressing in expanding clips Basement cleaning I found a brand new DMC RoofSpoiler! 10 Screws: 1.5 Nm 14 Self-tapping screw: 1.5 Nm Advertising - 5 Seal Hey guys, I have done this on my TT.. it requires a lot of work.. removing about 30 'rivets' and then filling the holes and re-paint.. it would be probably cheaper to find US spec bumpers and replace them..
Terms of Service -
Bumper Removal
Bumper Removal
Big Pics - Bumper Removal
PDF
Tools:- Jack, Axel stands Wheel brace &
Torque wrench (120nm), Full range of Torx bits, Large Philips driver, long reach
10mm socket driver, Pipe clamp for alien pipe if needed. 3. Slide headlight towards radiator in order to disengage mounting pin -1- from retainer -2-. 16 Self-tapping screw: 1.5 Nm 2nd gen. A3 - (Typ 8P/8PA, 2003present), Q5 Bumper Removal, S-Line Grille installation on standard bumper, WTB: ASAP 99/00 A4 or S4 front bumper and rear bumper, DIY- Custom bumper LEDs for my Canadian friends, FT: B6 A4 non s-line bumper + Cash for your USP bumper. Wow awesome article Andre. His work has appeared on various websites. Mine is scratched up and If I could just buy the lens, I can replace my old one using your instruction. Always set the emergency brake of the Audi TT before attempting to remove the front bumper to prevent the vehicle from moving. the bottom two holes line up with ones already in the front bumper but in order to get the top two in i need to take the bumper off and drill 2 new holes. 1 Not applicable If you find out please let me know, I would love to remove mine as it looks like s%^t! Trim -1- engages in side of guide profile If guide profile is not loosened, trim cannot disengage from retainers, and paintwork may be damaged. My Audi TT Mk1 8N Tuning Project galement en Franais. Loosen screw -3-. Detach before removing trim -1- Everything from Audi always recommends removing the tires. :thumb: A forum community dedicated to UK-based automotive detailing enthusiasts. Remove the entire plastic cover across the
front of the car, you will then have access to the 6 Torx screws at the front
holding the bumper.remove them, slide off the metal clamping strip and put it
to one side. Cookie Policy -
I'm hoping to get a rear telson spoiler to add more black to the color scheme. Trim -1- and bumper -5- removed Pingback: algum membro sabe como retirar o esguincho lava farois audi tt? 2 Height adjustment screw 
8N0941 004 AS. Those may be where you're having your problem. 4. Question: What is the difference between the following TT head light part numbers: 1 Front wheelhousing liner Remove the Front Wheelhousing Liner 7 Hexagon bolt: 35 Nm How do you remove the plastic fender from the bumper itself. Engage mounting pin -1- in retainer -2-. Place a wood block behind the rear tire to prevent the vehicle from rolling. 3 Combi screw: 6 Nm Trim -1- removed Here it goes: 1. Unscrew Torx screws -arrow A- and 2 screws from underside. The door inserts aren't supposed to come flush but do help come closer to the edge. Thanks for the blog. Disconnect the Torx bolts with a Torx bit and socket wrench. Do Not Sell My Personal Information -, By logging into your account, you agree to our. Audi TT Mk1 8n Tuning Parts & Accessories, Audi TT Performance Parts for sale (mk1 /8n), Audi TT LED (R8 LED Daytime Running Lights unlike POGEARACING), DMC Concept North America (Canada & USA) Tuning for yourAudi, Audi TT Tuning: Aesthetics AftermarketAccessories, Audi TT Suspension Performance: Control Arm Solution: DefconBushes, For Sale: 2002 2L 462 Bhp Jabbasport Audi TT(UK), How to remove the headlights of an Audi TTMK1, Waks Eclipse Lights & Clear/Smoke Corner Fitting. Every year of the MK1 TT; 1998-2006. Remove screws -3- and take off securing strip -2-. TIP: Once the pegs are pushed, use 2 flat tools to lever the head and entire peg
body out, as they are under tension, they could pop out, make sure a thumb or
finger is stopping them to catch them before they fly off and disappear into the
engine bay. Removing headlights Carl Pruit has been a freelance writer since 2005, specializing in service journalism and travel. Plug & Play comfort blinkers on a MK1 TT, yes itspossible! FYI, the DRLs are powered from the fog lamps. Besides the time savings, I like leaving the wheels on b/c I lean on the wheel while I am contorting my arm to undo the nuts and I also get sketchy about working under a car on jacks/stands. I see. I don't remove the wheels to pull the bumper, just undo the front halfs of both the wheel liners, then crank the wheels all the way to one side, undo the wheel well nuts on one side and then turn the wheels the other way to get access to the other side. 13 Expanding clip
2. Absolutely! Privacy Statement - 2 Detaching wheel spoiler TIP: get an empty plastic box or tray to collect your screws as you go along.
thank you for the post.can i transfer my 2002 TT Xenon hardware and place them into a 2002 halogen headlight assembly? c) Bentleys Repair Manual Headlight Removing Guide. 55K Km. I did it myself, the tumors are punched into the bumpers and held by clips. 8 Bracket Turn adjuster -2- as necessary to bring headlight housing in alignment with bumper trim. Great source of repair manuals. From the WAK-TT website for the 8N Mk1 model: Thought I would upload a couple of quick photo's taken of the completion of the thread I started. For a better experience, please enable JavaScript in your browser before proceeding. c) Disengage wheelhousing liner from fender and pull it out downward. It's better off to order the US spec bumpers from the dealer yeah i had the tumors i took them off right away! Park the Audi TT on a level surface and set the parking brake. Connect electrical connections. Since the two first removal guides are links, you will find Bentleys guide below. Archive -
Thanks Dubspeed. Remove front bumper trim Cheers Alan, appreciate your time given to reply. Change), You are commenting using your Twitter account. Install screws -arrows- and hand-tighten only. There are 2 10mm bolts either side, 1 is
accessible from the top half of a chamber, the other from the lower chamber,
loosen and remove these bolts. Born and raised in California, Pruit attended Contra Costa Community College in San Pablo, Calif. and received an associate degree in the administration of justice. To this day, I still havent found any supplier for the lenses. so what your saying is.if i wanted a right hand drive tt, i should import it to canada, register it there, then bring it to the us for registration? Is there any way of taking off the "tumors" from the canadian front and rear bumpers? Audi Forum - Audi Forums for the A4, S4, TT, A3, A6 and more! Manage Preferences -
Privacy Statement -
The front bumper of the Audi TT is connected to the front of the vehicle frame with screws and bolts that can be removed in about a half hour. 
So this install cancels the fog lamps, but the LED lights replace their lighting power! Disconnect electrical connections. To remove, unscrew bolts -7- and pull bracket out of longitudinal member Whats powering the DRL, is there wires being tapped etc.. Also, angel eyes, where is the power drawn? Unscrew when removing bracket -8- Advertising -
Install in reverse order of removal, noting the following: Archive -
might as well get something else, since you have to paint the bumper anyway. Remove screws -arrows-. Change), You are commenting using your Facebook account.
Change). If ever you find one, let me know! Remove screws -17- at bottom of trim from noise insulation. a) Waks Eclipse Lights & Clear/Smoke Corner Fitting (Step by Step Instructions with Images) Not sure, Id have to contact the right people. Unfortunately, I do cannot publish this information for competitive reasons. Remove the Battery Cover and all six pegs
holding the front cross member cover panel in. If alignment is necessary, proceed as follows:
To remove, unscrew combi bolt -4- and detach bumper But when you purchase the DRLs, you do get a complete install guide. b) Unscrew Torx bolts -2- (13x). To enable trim -1- to engage upon installation, press guide profile upward as far as it will go and tighten screws -10-. 11 Hexagon nut with collar: 6 Nm Reconnect battery, Tightening torque: Headlight housing to lock carrier: 6.5 Nm, Special tools, testers and auxiliary items needed : VAS 5107 Optical headlight aimer. Come join the discussion about performance, builds, modifications, classifieds, troubleshooting, maintenance, new releases, and more! but its about the middle of the bumper and on either side of where the grill is.